Untitled Document
Untitled Document
Untitled Document
BLAST POTS
(브라스트 포트)
BLAST CABINETS &
CLOSED CIRCUIT BLASTERS
(브라스트 캐비넷)
ABRASIVE RECOVERY &
RECYCLING SYSTEMS
(연마재 회수 장치)
ABRASIVES
(연마재)
BLAST WHEEL
REPLACEMENT PARTS
(브라스트 휠)
AIR BLAST ACCESSORIES &
REPLACEMENT PARTS
(브라스트 악세서리)
NEW PRODUCTS
신제품
 
HOME > 브라스팅 장비

Steel Shot

목록보기

Product Description and Technical Data:

PanaShot™ is manufactured by melting high quality steel scrap that is subsequently atomised by pouring streams of the molten steel through high-pressure water jets.

The resultant shots are then homogenised by reheating and then subsequently refined during quenching.

The shots are then dried and reheated in a tempering furnace to produce the applicable hardness. The tempered shots are then mechanically screened to produce 11 grades conforming to SAE standard specifications for blasting shots.

Grades of differing sizes and /or hardness's specifically for specialised applications i.e. shot peening are also produced.

PanaShot™ is produced under a controlled manufacturing process to achieve a product of uniform harness, density and microstructure; coupled with good toughness for durability.

These factors result in abrasive of sufficient hardness to perform its cleaning function as well as an extended life.

PanaShot™ is widely used as a media for descaling steel components prior to coating. I n this application the media is used almost exclusively in centrifugal wheel airless blasting equipment.

The round shape and relative softness of PanaShot™ ensures excessive wear is not imparted on the equipment.

PanaShot™ is also widely used in the foundry casting industry to remove sand from castings after removal from the mould.

When used in conjunction with the appropriate equipment, PanaShot™ is the ultimate abrasive blast media for steel cleaning or preparation due to its durability.

* Images for comparison purposes only

 

SAE S780 SAE S660 SAE S550 SAE S460 SAE S390
SAE Steel Shot Size Specifications:

 
Screen opening sizes and screen numbers with max. and min. cumulative percentage allowed on corresponding screens.
Screen
Screen
Metric
SAE Shot Number
No
Size (In)
Size (mm)
S780
S660
S550
S460
S390
S330
S280
S230
S170
S110
S070
7
0.1110
2.80
0%
8
0.0937
2.36
0%
10
0.0787
2.00
³ 85%
0%
0%
12
0.0661
1.70
³ 97%
³ 85%
≤ 5%
0%
14
0.0555
1.40
³ 97%
³ 85%
≤ 5%
0%
16
0.0469
1.18
³ 97%
³ 85%
≤ 5%
0%
18
0.0394
1.00
³ 96%
³ 85%
≤ 5%
0%
20
0.0331
0.850
³ 96%
³ 85%
≤ 10%
0%
25
0.0280
0.710
³ 96%
³ 85%
≤ 10%
30
0.0232
0.600
³ 96%
³ 85%
0%
35
0.0197
0.500
³ 97%
≤ 1 0%
40
0.0165
0.425
³ 85%
0%
45
0.0138
0.355
³ 97%
≤ 10%
50
0.0117
0.300
³ 80%
80
0.0070
0.180
³ 90%
³ 80%
120
0.0049
0.125
³ 90%
 
PanaShot™ Abrasive Properties:
Shape
Round, S pherical
Carbon %
0.8 - 1.2

Hardness (HRC)

Standard

Peening (Regular)

Special (Hard)

 

40 - 50

45 - 52

55 - 62
Silicon %
0.4 - 1.2
Bulk Density (kg/m³)
4450
Manganese %
0.5 - 1.2
Particle S.G
> 7.4
Sulphur %
< 0.05
Colour
Grey, Silver
Phosphorus %
< 0.05
Size Standard
SAE
Microstructure
Martensite and Bainite
 
PanaShot™ Packaging:
25 kg Bags 1 Tonne Pallet (40 x 25 kg Bags)
600 - 1000 kg Drum  
 
PanaShot™ Ordering Information:
Stock Code ASA - STS XXXY
Key XXX - Product SAE Number (e.g. 110 for SAE S110)
Y - Blank for Standard SAE Grade
P for Peening Grade (45 - 52 HRC)
L for Peening Grade (55 - 62 HRC)
D for packing in Drums
 

Note - Figures may vary depending on raw materials and manufacturing processes used.Contact Pan Abrasives for further information.

 
 
Untitled Document